Skip to main content

Licensed & Insured — Lic. #1027421

747-255-8595
911 Construction & Electric Inc. logo

Electrical Tips

LADWP Panel Upgrade Steps: From Service Planning to Power

6 min read

Gray meter-main with a blank circular meter cover and an open gray load center with black plug-in breakers on a beige stucco wall beside a white garage door, with succulents in gravel at the base.

Most of the City of Los Angeles gets its power from the Los Angeles Department of Water and Power (LADWP), and that changes how a panel upgrade works in neighborhoods like Eagle Rock, Highland Park, Los Feliz, Sunland, Tujunga, North Hollywood and Van Nuys. Two City departments are involved: LADWP decides where your new meter and panel can go and when the power comes back on, and the Los Angeles Department of Building and Safety (LADBS) issues the electrical permit and inspects the work. Here's the LADWP and LADBS sequence for 2026, step by step, with the timelines LADWP itself publishes. Planning an upgrade? Request a free estimate or call 747-255-8595.

LADWP, LADBS and Your Electrician: Who Does What

  • LADWP handles the utility side. Its Electric Service Planning staff (an Electric Service Representative, or ESR, for most homes) confirms the meter and panel location, tells you whether LADWP's own equipment needs work, and sets the meter at the end. LADWP's Find the Right Person tool matches your address to the right service planning contact.
  • LADBS issues the electrical permit and inspects the new service equipment and wiring.
  • Your C-10 electrician sizes the service, requests the meter spot, pulls the permit and books inspections.

One check before anything else: look at your electric bill. A few pockets inside City of LA neighborhoods are on SCE, and Pasadena, Glendale and Burbank each run their own utilities, so these LADWP steps don't apply there.

Step 1: Size the Service and Request a Meter Spot

Every panel upgrade starts with a load calculation: what the house uses now plus what's coming, such as an EV charger, heat pump, induction range, spa or ADU. LADWP's 2025 Electric Service Requirements treat added load on an existing service as a new installation, so LADWP reviews it and can require changes to its own facilities, up to transformer provisions on the property.

Next comes the meter spot. LADWP says that when a contractor or homeowner plans to install a new residential service panel, they must first request one. It's free, and it confirms where the new panel and meter may go, which isn't always where the old one was:

  • Single-family services up to 320 amps can be requested through LADWP's online meter spot request.
  • An ESR schedules a site visit within 5 to 15 business days and leaves a sketch of the approved location at the property. The LADBS inspector may ask to see it before approving the panel.
  • A panel larger than a single 225-amp panel also needs LADWP's Residential Service Planning Information Form, which includes a load schedule. Services over 320 amps go through the LADWP Connection Center at (213) 367-6937.

Step 2: The LADBS Electrical Permit

For most homes this is the quick part. LADBS Information Bulletin P/GI 2026-003 lists electrical installations under 600 volts and up to 400 amps total load in existing residential buildings as Express Permits, meaning no plan check, as long as the wiring isn't engineered. An EV charger job that includes a service upgrade up to 400 amps is on the same list. Larger or engineered services go through LADBS plan review instead.

We pull the permit under our C-10 license. The details on it (address, main breaker size, phase, wires and voltage) have to match, because LADWP says the LADBS release it receives must correspond to the service information on the permit. For general permit questions, see our Los Angeles electrical panel permit guide.

Step 3: Installation, Inspection and the LADBS Release

LADWP's Guide to Electric Service asks contractors to notify the ESR five working days before construction. When the work is ready, the inspection is requested online or through 311. LADBS says work isn't approved until its inspector has inspected and accepted it.

For overhead services rated up to 200 amps single-phase, LADWP's service requirements say the LADBS inspector performs the final inspection for LADWP. After you pass, LADBS sends an electronic release to LADWP, and LADWP warns it can take several days to arrive. LADWP energizes only after the installation is cleared by both LADBS and LADWP and any LADWP charges are paid.

Can the house stay powered in between? LADWP allows a temporary unmetered "flat connection" during alterations that require removing the meter, but only with approval from both LADWP and the inspection authority, and for no more than seven working days. Longer than that needs a metered temporary service. We plan this before the work date, especially if someone at home relies on medical equipment.

100 Amp to 200 Amp Service Upgrade: The LADWP Timeline

Going from 100 to 200 amps is a common upgrade for older City of LA homes adding an EV charger, heat pump or induction range. LADWP's 2025 Electric Service Requirements publish a typical sequence for an overhead residential service:

  1. Request for service to LADWP requirements: 2–6 weeks
  2. LADWP off-site work (conductors, transformer), if needed: 2–4 weeks
  3. Install, LADBS inspection and release: depends on the job
  4. LADWP energizes and sets the meter: 5–10 days

LADWP adds that timelines vary with workload and asks customers to check with their assigned ESR for current ones. Many 100A-to-200A jobs need no off-site LADWP work, and underground-fed homes follow a different chart. For budgets, see our panel upgrade cost guide.

Using the LADWP EV Charger Rebate Toward the Panel

If the upgrade is for an EV charger, LADWP's Residential EV Charger Rebate currently lists, as of Nov 16, 2026, up to $1,000 toward the purchase and installation of a qualifying charger, plus $500 more for Lifeline or EZ-SAVE customers (up to $1,500) and $250 for a dedicated EV meter. LADWP's FAQ counts panels, breakers, meter sockets, wiring and permits as eligible costs when a licensed electrician does the work, and it requires a "Finaled" LADBS permit. LADWP also asks you to book a service assessment before installing. Confirm current terms with LADWP. Our LADWP EV charger rebate guide and EV charger installation page cover the rest.

Frequently Asked Questions

Does LADWP have to approve my panel upgrade?

Yes. LADWP requires a meter spot before a new residential service panel goes in, and it energizes the new service only after both LADBS and LADWP have cleared the installation.

How long does an LADWP meter spot take?

LADWP's meter spot page says an ESR schedules the site visit within 5 to 15 business days and leaves a sketch of the approved panel location at the property.

Does a 200-amp panel upgrade in LA need plan check?

Usually not. LADBS lists non-engineered electrical work up to 400 amps total load in existing homes as an express permit. We still pull the permit, and LADBS still inspects.

When does LADWP turn the power back on?

After the LADBS final and release, LADWP's published typical time to energize and set the meter is 5 to 10 days. LADWP says timelines vary with workload, so ask your ESR.

Can the LADWP EV rebate help pay for a panel upgrade?

It can. LADWP lists panels and breakers among eligible installation costs for a qualifying charger, within the rebate cap, as of Nov 16, 2026.

Upgrading Your Panel on LADWP? Talk to a Licensed C-10 First

911 Construction & Electric Inc. is a licensed, bonded and insured C-10 electrical contractor (CA Lic. #1027421) at 1308 E Colorado Blvd Ste 141, Pasadena, CA 91106, serving Pasadena, Altadena, Glendale, Burbank, Arcadia, the San Gabriel Valley and greater Los Angeles. We handle LADWP meter spots, LADBS permits, inspections and 100A-to-200A panel upgrades for homes in Eagle Rock, Highland Park and across LADWP territory. Request a free estimate, call 747-255-8595 or visit https://911electrics.com. 24/7 emergency service available.

Was this helpful?

Have an electrical project in mind?

Talk to a licensed electrician today — free estimates, 24/7 emergency service.

Call 24/7Free Quote